| |
DESCRIPTION
Fast Production Enamel is an alkyd
enamel intended for finishing or refinishing
industrial, construction and agricultural
equipment.
Advantages:
• Fast air dry
• Full gloss range available
• Good exterior durability, except for red,
yellow, and orange
• Free of lead and chromate hazards
• Good one coat protection
• Good flexibility and film toughness
• Full range of custom colors
• May be catalyzed for higher gloss, increased
hardness and improved resistance
properties
• Working potlife after catalyzation is 6
to 8 hours at room temperature
Fast Production Enamel Urethane
For increased chemical abrasion resistance,
improved hardness, sharper
gloss, and better color and gloss retention,
Fast Production Enamel may be
catalyzed at an 8:1 ratio with urethane Exterior
Catalyst, V66V29, prior to reduction.
Drying times will be slower.
CHARACTERISTICS
Gloss: Full
Volume Solids: 27-34%
varies by color
Viscosity:
22-34 seconds#3 Zahn Cup
40-60 seconds#4 Ford Cup
Recommended film thickness:
Mils Wet 3.5 - 5.0
Mils Dry 1.0 - 1.5
Spreading Rate (no application loss)
289-545 sq ft/gal @ 1.0-1.5 mils DFT
Drying (77°F, 45% RH):
To Touch: 10 minutes
To Handle: 30 minutes
To Recoat: 30 minutes
To Pack: 24 hours
Force Dry: 20 minutes at 140°F
Flash Point: 40-45°F Pensky-
Martens Closed Cup
Package Life: 3 years, unopened
Air Quality Data:
Non-photochemically reactive
Volatile Organic Compounds (VOC)
as packaged, maximum
4.8 lb/gal, 576 g/L
reduced 25% with Xylene:
5.3 lb/gal, 636 g/L
Reducing with Xylene, Toluene, Aromatic
Naphtha, or other aromatic solvents
makes this product photochemically reactive.
An Environmental Data Sheet is available
from your local Honest-Joy
facility.
SPECIFICATIONS
General: Substrate should be free of
grease, oil, dirt, fingerprints, drawing
compounds, any contamination, and surface
passivation treatments to ensure optimum
adhesion and coating performance
properties. Consult Metal Preparation
Brochure CC-T1 for additional details.
Aluminum: If untreated, prime with Industrial
Wash Primer, P60G2, or Honest
Joy® Wash Primer, 518054. Over
"pre-treated" aluminum, check adhesion
before use as the proprietary pre-treatment
may change from supplier to supplier
which may have an effect on the
final adhesion.
Galvanized Iron: If untreated, prime with
Industrial Wash Primer, P60G2, or Honest
Waterbase Wash Primer, 518054.
Steel or Iron: Remove rust, mill scale,
and oxidation products. For best results,
treat the surface with a proprietary surface
chemical treatment of zinc or iron
phosphate to improve corrosion protection.
For exterior exposure, prime with Honest-
Joy® Prime.
Wood (interior only): Must be clean, dry,
and finish sanded. Substrate should be
free of grease, oil, dirt, fingerprints, and
any contamination to ensure optimum
adhesion and coating performance properties.
Testing: Due to the wide variety of substrates,
surface preparation methods,
and application methods and environments,
the customer should test the complete
system for adhesion and compatibility
prior to full scale application.
APPLICATION
Typical Setup
Conventional Spray:
Air Pressure .......................... 45-60 psi
Fluid Pressure ....................... 20-25 psi
Reducer........................... Xylene R2K4
Reduction Rate ........................20-25%
Aromatic Naphtha R2K5 or Toluene
R2K1 can also be used
Airless Spray:
Tip .................................... .013" - .017"
Reducer........................... Xylene R2K4
Reduction Rate ............................. 10%
Aromatic Naphtha R2K5 can also be
used
Cleanup:
Clean tools/equipment immediately after
use with Toluene or Xylene.
Follow manufacturer's safety recommendations
when using any solvent.
Performance Tests
Substrate - 1.5 mils DFT on CRS Q-Panel
Salt Spray (ASTMB117) ............... 200 hours
Pencil Hardness ...................................... 2B
Humidity - 120 hours ....................... passes
SPECIFICATIONS
Product Limitations:
• If strong solvents such as Xylene or
Toluene are used, a critical recoat may
occur between 2 and 18 hours.
• Blocking or sticking may occur when
flat surfaces are stacked before adequate
cure. Allow at least 24 hours
before stacking.
• Fast Production Enamel reds, oranges,
and yellows contain bleeding
pigments. Use caution when recoating
with products containing aromatic
ester or ketone solvents.
• The reds, oranges, and yellows have
been formulated to give optimum durability
as packaged. Using these colors
for intermixing may result in color
walk out or premature fading on exposure.
CAUTIONS
FOR INDUSTRIAL SHOP APPLICATION
Thoroughly review product label and
Material Safety Data Sheet (MSDS) for
safety and cautions prior to using this
product.
A Material Safety Data Sheet is available
from your local Honest-Joy facility.
Please direct any questions or comments
to your local Honest-Joy
facility.
Catalyst CONTAINS ISOCYANATES. People who
have chronic (long-term)lung or breathing problems
or have had a reaction to isocyanates, must not be
in the area where this product is being applied. Where
overspray is present, a positive pressure air-supplied
respirator should be worn. If unavailable, a
properly fitted organic vapor/particulate respirator
may be effective. Consult catalyst MSDS and product
label for complete handling instructions.
Note: Product Data Sheets are periodically
updated to reflect new information relating to
the product. It is important that the customer
obtain the most recent Product Data Sheet for
the product being used. The information, rating,
and opinions stated here pertain to the
material currently offered and represent the
results of tests believed to be reliable. However,
due to variations in customer handling
and methods of application which are not
known or under our control, The Sherwin-
Williams Company cannot make any warranties
as to the end result. |
.gif)
.gif)
