|
Epoxy Systerm
General Properties
This two-component high build epoxy offers very good impact and
abrasion resistance from heavy foot traffic. Resists acid, chemicals
and strong cleaning compounds. Dried film does not support
mold, mildew or fungi growth. This non-toxic coating has superior
resistance to salt and fresh water. The high solids of this coating
permit good leveling and filling of old, abused floor areas.
Available in clear as well as a variety of colors.
Features:
• Extremely durable stain resistant film
• High solids, thick film coating
• Very good impact and abrasion resistance
• Good acid and chemical resistance
• Very good alkali resistance
• Resists strong cleaning compounds
• Solvent resistant
• Tile-like finish does not support mildew or fungi growth
• Good immersion in fresh and salt water
• Resists high abuse traffic
• Forms insulating barrier coat
Limitations:
• Gloss reduction and tendency to yellow on exterior surfaces
• Slight ambering in the presence of strong ultraviolet light and
ammonia compounds
• When used as a floor coating, apply at a rate of 150 sq.ft./gal.
and consider the need for an anti-slip aggregate
• Does not cure below 55° F
Recommended For:
Use on properly prepared surfaces exposed to high abuse. For use
in refurbishing abused concrete floors. Forms a tough, dense,
waterproof film on floors and walls. Provides an effective
insulating barrier for corrosion control. For water and waste
treatment plants, food processing plants, dairies, chemical plants,
pulp and paper mills, bottling plants, pharmaceutical plants,
bakeries, power generating plants, storage tanks, equipment,
machinery, catwalks, railings, and stairs.
Waterborne Urethane System
General Description
The latest in waterborne technology, this product is formulated to
perform as a durable gloss finish coat. This waterborne acrylic
urethane offers no fire hazard and is non-polluting. It provides
resistance to various weather conditions, oxidation, fading and
loss of gloss. This tough flexible film provides the adhesion
needed to withstand thermal shock due to radical weather
changes. Excellent adhesion to a variety of substrates. Also
available in a non-yellowing clear.
Features:
• Water thinned
• Fast dry and recoat times
• Excellent adhesion
• Resists oxidation, fading, and
loss of gloss
• Excellent weathering
properties
• Excellent abrasion resistance
• Low odor
• Gloss finish
• Excellent impact resistance
• Flexible finish
• Contains UV Absorbers For
Exterior Durability
Recommended For:
• Ferrous or non-ferrous metal
• Interior or exterior surfaces
• Wood trim
• Masonry surfaces
• Protects tanks
• Equipment
• Conveyors
• General maintenance painting
• Structural or support steel
• Roof vents
Limitations:
• Not for immersion service
• Not for high abuse floor areas
Alkyd System:
General Description
This rapid dry gloss enamel is formulated for interior or exterior
use on surfaces requiring a coating that dries to the touch in 30
minutes. Available in unlimited custom tinted colors. This product
permits equipment to be coated while it is being repaired
eliminating additional down time to allow paint to dry.
Features
• Dry to touch in 30 minutes
• Unlimited custom tinted colors
• Interior or exterior use
Recommended For:
• Equipment
• Metal Doors and Cabinets
• Walls and Dadoes
• Machinery
• Tanks and Drums
• Structural Steel
• Metal Roof Decks and Open Bar Joist
• Catwalks, Railings, and Piping
Limitations:
• Not for immersion service
• Not for application directly on galvanized metal
• Not for floor areas
• Recoat within 3 hours or wait at least 36 hours
• The solvents in this product may lift previously applied
coatings. Test a small area before applying a full coat.
Acrylic System:
General Properties
This product is designed to perform a dual purpose as a direct to
metal primer and finish. Both coats of the product provide rust
inhibition for superior corrosion control. The acrylic formula
provides excellent gloss and color retention. The film is fast drying,
permitting fast recoat.
This product is also an excellent finish for masonry, plaster,
wallboard and interior wood surfaces.
Features
• Direct to metal application
• Water thinned
• Fast dry and recoat times
• Excellent adhesion
• Resists oxidation, fading, and loss of gloss
• Standard line of colors
• Unlimited custom colors
• Corrosion resistant
• No fire hazard
• Non-polluting
• High gloss finish
Recommended For:
• Ferrous or non-ferrous metal
• Interior or exterior surfaces
• Wood
• Masonry surfaces
• Equipment
• Fencing
• Metal storage sheds
• Bilco® doors and railings
• General maintenance painting
• Structural or support steel
• Roof decks
• Bar joists
• Roof vents
Limitations:
• Not for immersion service
• Not for strong chemicals
• Minimum film forming temperature 50° F
• Ferrous or non-ferrous metal |