|
|
|
|
|
|
|
|
|
| |
 |
Epoxy Paste Adhesive For Bonding Traffic Markers To Pavement Coating/Paint
|
|
| |
For Details, Click Here to Send Us an Inquiry At: sales@epoxy-paint.cn to see if this Epoxy Paste Adhesive For Bonding Traffic Markers To Pavement is right for your application. |
| |
 |
| |
Epoxy Paste Adhesive For Bonding Traffic Markers To Pavement
Honest Bonder Paste, Traffic Marker is a two-component, short working life, non-sag, epoxy paste adhesive
designed for application on pavements to bond traffic markers and preformed curbs and car stops in
parking lots. The product meets the State of California Specification 8040-51M-09, "Standard Set Epoxy
Adhesive for Pavement Markers." Suitable substrates include concrete, masonry, stone and asphalt. All
substrates must be surface dry at the time of epoxy adhesive application. Bonder Paste, Traffic Marker
features a convenient 1 : 1, by volume component mix ratio. Its buttery nature contributes to ease of
application and efficient product use. The components do not contain volatile solvents (VOC's). |
| |
| |
FEATURE
Convenient 1 : 1, by vol. mix ratio
Short work life/fast cure for short downtime
Non-sag consistency for efficient use
Meets State of California Specification 8040-51M-09
Environmentally safe-No VOC solvents
Limitations: Substrates must be surface dry. The
recommended minimum substrate temperature during
installation and for cure is 50 deg F. The recommended
maximum substrate temperature during application is 100
deg F. When hand mixing the adhesive, it is recommended
that not more than one quart be mixed at one time, and the
markers aligned and pressed into place within five minutes
after mixing operations are started. Do not add solvents or
otherwise thin this material.
Packaging & Colors: Standard package sizes of Part A +
Part B are 2 and 10 gallons. Color is Concrete gray (bluegray).
Shelf Life: Three years minimum in unopened, original
containers when stored between 60 and 90 dog F in a dry
place away from sunlight. Remixing of components may be
required upon prolonged storage.
Chemical Resistance: Bonder Paste, Traffic Marker has
excellent resistance to a wide range of commonly
encountered deicing chemicals, salts and aircraft and
automotive fluids. It has limited resistance to hydrocarbon
solvents. Performance is a function of the specific chemical
and concentration, exposure times and housekeeping
procedures. For information on specific chemicals and
exposure conditions, contact us for details., |
| |
|
| |
Surface Preparation Substrates must be surface dry, sound
and free of all bond-inhibiting substances. Prepare surfaces in
accordance with ASTM D 4259 or ACI 503R and ChemCo
Systems' specific recommendations. Remove all loose,
unsound and deteriorated pavement surface layers. Cleaned
concrete surfaces should have a minimum strength of 250 psi
in direct tension.
Mixing: Bonder Paste, Traffic Marker is a two-component
system. The resin to hardener (Part A : Part B) mix ratio is 1:1,
by volume. Read all material safety data (MSDS) information
before handling the product. Wear safety glasses and clean
neoprene rubber gloves when handling the materials. Premix
the individual components before drawing from bulk packaging.
Transfer the appropriate quantities of Part A and Part B into a
mixing container. Use quantities that can be applied before the
pot life of the material expires. When hand mixing the
adhesive, it is recommended that not more than one quart be
mixed at one time. Blend thoroughly using a Jiffy mixer blade
attached to a low speed (350 - 750 rpm) electric or pneumatic
drill. Proper mixing will take 2 - 3 minutes.
Installing: Apply mixed material uniformly on the cleaned
pavement surface or on the bottom of the marker in a quantity
sufficient to result in complete coverage of the area of contact
of the marker with no voids present and with slight excess after
the marker has been pressed into place. The marker is placed
in position end pressure applied until firm contact is made with
the pavement. Immediately remove excess adhesive around
the edge of the marker, excess adhesive on the pavement, and
adhesive on the exposed surfaces of the markers. Clean
mixing and application tools frequently.
Clean up: Excess mixed product is best removed from the
work area and tools before it hardens. Use of rags and solvents
such as acetone or heavy-duty detergents facilitate cleaning.
Cured product may be removed from tools by soaking in an
epoxy stripper. |
|
| | |
|
| | |
 |
 |
 |
| All Rights Reserved by
Feiyang ® Honest Joy Coating/Paint | |
 | |
|
.gif)
.gif)
