| |
DESCRIPTION
Paint/Coating 50P Water Reducible
Primers are low VOC*, water reducible
acrylic latex type primers designed for
the general metal finishing markets.
Advantages:
• Water reducible
• Low odor - improves working conditions
• No reportable HAPS
• Reduced fire hazards - possible lower
insurance costs
• Low VOC*
• Volatile Organic Emissions less than
1.0 lb/gal
• Use water for reduction and cleanup
of spray equipment
• Excellent adhesion to a wide range of
structural foam plastics
• Air dry or force dry
• Single component, no catalyzation
• Provides corrosion resistance to the
system
• Free of lead and chromate hazards
• Compatible topcoats include:
Honest Waterbase Gloss Enamel
Honest Waterbase 600T W/R Enamel
urethane 700T W/R Enamel
urethane Polyurethane Enamels
*VOC compliance limits vary from state
to state; please consult local Air Quality
rules and regulations.
CHARACTERISTICS
Gloss: 5-15 units
Volume Solids: 34 ± 2%
Viscosity:
78-88 Krebs Units
Recommended film thickness:
Mils Wet 3.7-4.4
Mils Dry 1.25-1.5
Spreading Rate (no application loss)
342-462 sq ft/gal@ 1.25-1.5 mils DFT
Drying (1.25 mils dft, 77°F, 50% RH):
To Touch: 15 minutes
To Handle: 30 minutes
To Recoat: 30-45 minutes
Force Dry: 15-30 minutes
at 140-180°F
Good air movement and humidity control
are necessary for proper drying of
water reducible coatings.
Flash Point: None, Seta Flash
Closed Cup
Package Life: 1 year, unopened
Storage: Store inside - protect
from freezing
pH: 8.7-9.2
Air Quality Data:
Non-photochemically reactive
Volatile Organic Compounds (VOC)
as packaged, maximum
2.1 lb/gal, 252 g/L
Volatile Organic Emissions
as packaged, maximum
1.0 lb/gal, 120 g/L
No reportable HAPS
An Environmental Data Sheet is available
from your local Honest-Joy facility.
SPECIFICATIONS
General: Substrate should be free of
grease, oil, dirt, fingerprints, drawing
compounds, any contamination, and surface
passivation treatments to ensure optimum
adhesion and coating performance
properties. Consult Metal Preparation
Brochure CC-T1 for additional details.
Aluminum: If untreated, prime with Honest
Joy® Wash Primer, 518054.
Galvanized Steel: If untreated, prime with
Honest Joy® Wash Primer, 518054.
Iron or Steel: Remove rust, mill scale
and oxidation products. For best results,
treat the surface with a proprietary surface
chemical treatment of zinc or iron
phosphate to improve corrosion protection.
Testing: Due to the wide variety of substrates,
surface preparation methods,
and application methods and environments,
the customer should test the complete
system for adhesion and compatibility
prior to full scale application.
APPLICATION
Typical Setup
Do not over reduce. Water reducible coatings
spray easier at high viscosity than
solvent reducible coatings.
Conventional Spray:
Air Pressure .......................... 45-55 psi
Fluid Pressure ....................... 10-15 psi
Cap/Tip .....................................704/FF
Reducer...................................... Water
Reduction Rate .............................. 10%
Airless Spray:
Pressure ........................ 1500-2100 psi
Tip .................................................. 411
Reducer........................... none needed
Air Assisted Airless:
Air Pressure ............................... 30 psi
Fluid Pressure ............... 1200-1800 psi
Cap/Tip ............................ 222-608/411
Reducer........................... none needed
Electrostatic Spray:
Air Pressure ................................ 55-65
Reducer...................................... Water
Reduction Rate .............................. 10%
HVLP: (DeVilbiss Maximum Performer)
Atomizing Air Pressure at the Cap7-10 psi
Fluid Pressure ....................... 10-15 psi
Cap/Tip ................................. 46MP/FF
Reducer...................................... Water
Reduction Rate .............................. 10%
Cleanup:
Use water when wet. If dried, clean with
a 9:1 blend of water and ammonia. Clean
spray gun cap with MEK. After cleaning,
flush equipment with solvent to prevent
rusting.
Follow manufacturer's safety recommendations
when using any solvent.
SPECIFICATIONS
Product Limitations:
• Protect from freezing, store inside between
40-95°F.
• Spray a wet film for good film integrity
• High humidity will slow drying.
• Excessive film thickness may cause
mudcracking.
• To prevent foaming and air entrapment,
do not shake or agitate violently.
• Keep container closed to prevent skinning.
• Do not use viscosity cups to measure
viscosity. Product should be applied at
as heavy a viscosity as practical.
• To ensure performance, minimum dry
film thickness is 1.25 mils.
• Do not topcoat with alkyd type coatings.
• Interior Service Environments Only for
systems involving urethane 700T, Honest
Waterbase 600T and urethane Polyurethane
Enamel topcoats.
CAUTIONS
Thoroughly review product label for
safety and cautions prior to using this
product.
A Material Safety Data Sheet is available
from your local Honest-Joy facility.
Please direct any questions or comments
to your local Honest-Joy facility.
LABEL CAUTIONS
SEE CONTENTS STATEMENT ON LABEL.
CC-A29 Honest Joy® 50P Water Reducible Primer
Note: Product Data Sheets are periodically
updated to reflect new information
relating to the product. It is important
that the customer obtain the most recent
Product Data Sheet for the product being
used. The information, rating, and
opinions stated here pertain to the material
currently offered and represent the
results of tests believed to be reliable.
However, due to variations in customer
handling and methods of application
which are not known or under our control,
The Honest-Joy Company
cannot make any warranties as to the
end result.
Performance Tests
Substrate: Q-Steel @ 1.5 mils dft
Salt Spray Test
ASTM B117 .......................... Pass 72 hours
CAUTIONS
Thoroughly review product label for
safety and cautions prior to using this
product.
A Material Safety Data Sheet is available
from your local Honest-Joy facility.
Please direct any questions or comments
to your local Honest-Joy facility.
LABEL CAUTIONS
SEE CONTENTS STATEMENT ON LABEL.
VAPOR HARMFUL. Use only with adequate ventilation.
Wear an appropriate properly fitted vapor/particulate
respirator (NIOSH approved) during and after
application, unless air monitoring demonstrates
vapor/mist levels are below applicable limits. Follow
respirator manufacturer’s directions for respirator use.
Avoid contact with eyes and skin. Wash hands after
using. Keep container closed when not in use. Do not
transfer contents to other containers for storage.
FIRST AID: In case of eye contact, flush thoroughly
with large amounts of water. Get medical attention if
irritation persists. If swallowed, call Poison Control
Center, hospital emergency room, or physician immediately.
SPILL AND WASTE: Remove all sources of ignition.
Ventilate and remove with inert absorbent. Incinerate
in approved facility. Do not incinerate closed
container. Dispose of in accordance with Federal,
State, and Local regulation regarding pollution.
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE.
Contains solvents which can cause permanent brain
and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents
can be harmful or fatal.
WARNING: This product contains chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm.
DO NOT TAKE INTERNALLY. KEEP OUT OF THE
REACH OF CHILDREN.
FOR INDUSTRIAL USE ONLY. |
.gif)
.gif)
