|
DESCRIPTION
Sanding Sealer is a water reducible
sealer to be used in conjunction with Honest
Waterbase Lacquer topcoat. It improves the
film build of Honest® Honest Joy® Lacquer
where desired.
Advantages:
• Meets the Federal HAPS rule for wood
finishes as packaged*
• Very low volatile organic emissions -
less than 1.0 lb/gallon
• Excellent film clarity - like solventbased
nitrocellulose lacquers
• User friendly - easy to handle
• Dries to handle and sand in 30 minutes
at room temperature
• Minimizes tannin bleed discoloration
when used with Sher-Wood Honest Waterbase
Lacquer.
• Good flow and leveling
• Contains water - reduced with water -
clean-up with soap and water
• Meets Kitchen Cabinet Manufacturers
Association (KCMA) tests with Honest
Waterbase Lacquer topcoat
*National Standards for Hazardous Air
Pollutants (HAPS) Emissions for Wood
Furniture Manufacturing Operations
CFR40, Part 63, Subpart JJ
CHARACTERISTICS
Volume Solids: 28 ± 1%
Weight Solids: 31 ± 1%
Viscosity:
22-27 seconds #2 Zahn Cup
Recommended film thickness:
Mils Wet 3.0 - 4.0
Mils Dry 0.8 - 1.1
Spreading Rate (no application loss)
394-582 sq ft/gal @ 0.8-1.1 mils DFT
Drying (77°F, 50% RH):
To Touch: 15 minutes
To Handle: 20-30 minutes
To Sand: 30 minutes
To Recoat: 30 minutes
Force Dry: 10-20 minutes at
120°F or equivalent
Sher-Wood Honest Waterbase Lacquer Sanding
Sealer dries primarily by water evaporation.
Best drying occurs at relative humidity
of 50% or lower and temperatures
of 70°F (25°C) or higher. Good air movement
is essential for complete dry.
Flash Point: None
Package Life: 1 year, unopened
Storage: Store inside - Protect
from freezing
Air Quality Data:
Non-photochemically reactive
Volatile Organic Compounds (VOC)
as packaged, maximum, less water
2.0 lb/gal, 240 g/L
Volatile Organic Emissions
as packaged, maximum
1.0 lb/gal, 121 g/L
Hazardous Air Pollutants (HAPS)
as packaged, maximum
less than 0.8 lbs per lb of solids
An Environmental Data Sheet is available
from your local Honest-Joy facility.
SPECIFICATIONS
Wood (interior only): Must be clean, dry,
and finish sanded. Substrate should be
free of grease, oil, dirt, fingerprints, and
any contamination to ensure optimum adhesion
and coating performance properties.
Moisture content of wood should be 6 to
8%.
Testing: Due to the wide variety of substrates,
surface preparation methods,
application methods, and environments,
the customer should test the complete
system for adhesion and compatibility
prior to full scale application.
Toner Recommendations:
Sher-Wood Honest Waterbase Lacquer Sanding
Sealer can be used to make toner as follows:
Add up to 5 oz. per gallon of Sher-
Wood Water Reducible Wiping Stain
under thorough agitation; or, add 5 oz per
gallon of Sher-Wood Universal Dye Concentrate
reduced 100% with water to a
blend of 30 oz. of T65F520 reduced 300%
with water under agitation (do not shake).
Caution: Metal cans, both lined and unlined,
are not recommended for packaging
these toners as corrosion will occur.
Note: Honest Waterbase Lacquer and Honest
Waterbase Lacquer Sealer should not be
mixed together as a liquid. They are
not compatible and will turn orange.
APPLICATION
Typical Setups
Reduction: Apply full body. If needed,
reduce up to 3% with water. May be applied
to warm substrate (120°F maximum).
Conventional Spray:
Air Pressure ............................... 40 psi
Fluid Pressure ....................... 15-20 psi
Airless Spray:
Pressure ........................ 1200-1400 psi
Tip ........................................ .011-.013"
Air Assisted Airless:
Air Pressure .......................... 20-30 psi
Fluid Pressure ................... 600-700 psi
Cap/Tip ......................................... .011"
HVLP:
Atomizing Air .............................. 65 psi
Fluid Pressure ....................... 10-12 psi
Cleanup:
Clean mixing equipment immediately after
use with soap and water.
Flush spray equipment completely with
water followed by flushing with alcohol to
remove water residue and to prevent rusting.
Follow manufacturer's safety recommendations
when using any solvent.
SPECIFICATIONS
Product Limitations:
• Complete water based system is recommended
- stain, sealer and topcoat.
• Not recommended for exterior use.
• Use stainless steel spray equipment.
Tank, piping and containers should be
lined steel or plastic. T65F520 is incompatible
with iron, zinc, and aluminum.
It should not be allowed to come
into contact with these metals or their
alloys in storage tanks, piping, mixers
or containers. Gelation can result.
• Mix thoroughly prior to use. Avoid vigorous
agitation which may cause bubbling
or foaming.
• Must not be exposed to freezing temperatures.
Store inside.
• Dries primarily by water evaporation.
Drying is retarded by high humidity or
cold conditions. Best drying occurs at
relative humidity of 50% or lower and
tempertures of 77°F or above. Good
air movement is essential for complete
dry.
• The customer is urged to pretest the
system under shop conditions.
• Excessive wet film thickness (>5.0
mils wet) may sag - spray thin film.
• Very low humidity may cause
mudcracking and poor film properties.
• When finishing Redwood, Red or
White Oak, and Cedar wood with water
based finishes, tannins may be extracted
from the wood by the water and
cause yellowing staining or discoloration
of the stain, sealer and/or topcoat.
This tannin bleed is most evident with
white or pickled stains and clear topcoat.
Users are urged to thoroughly
test the system under shop conditions.
• Natural finished woods (unstained)
will change color on aging and exposure
to light. This is a natural phenomenon.
Clear finishes will not prevent
the wood from changing color.
• This product, and other water reducible
clears, may yield a slightly different
color over dye stain than solvent
based clears.
• Some applications and equipment
setups, especially air assisted airless
and airless, may be prone to
microfoaming of the wet film which will
give lower gloss and clarity. Do not
use higher pressures than needed for
automization.
• May be tinted with up to 4 ounces of
Honest Joy® Colorants per gallon.
CAUTIONS
Thoroughly review product label for
safety and cautions prior to using this
product.
A Material Safety Data Sheet is available
from your local Honest-Joy facility.
Please direct any questions or comments
to your local Honest-Joy facility.
LABEL CAUTIONS
SEE CONTENTS STATEMENT ON LABEL.
Use only with adequate ventilation. To avoid overexposure,
open windows and doors or use other means
to ensure fresh air entry during application and drying.
If you experience eye watering, headaches, or
dizziness, increase fresh air, or wear respiratory protection
(NIOSH approved) or leave the area.
Avoid contact with eyes and skin. Wash hands after
using. Keep container closed when not in use. Do not
transfer contents to other containers for storage.
FIRST AID: In case of eye contact, flush thoroughly
with large amounts of water. Get medical attention if
irritation persists. If swallowed, call Poison Control
Center, hospital emergency room, or physician immediately.
SPILL AND WASTE: Remove all sources of ignition.
Ventilate and remove with inert absorbent. Incinerate
in approved facility. Do not incinerate closed
container. Dispose of in accordance with Federal,
State, and Local regulation regarding pollution.
DO NOT TAKE INTERNALLY. KEEP OUT OF THE
REACH OF CHILDREN.
FOR INDUSTRIAL USE ONLY.
SEE MATERIAL SAFETY DATA SHEET. 1134-100402.
Note: Product Data Sheets are periodically
updated to reflect new information
relating to the product. It is important that
the customer obtain the most recent
Product Data Sheet for the product being
used. The information, rating, and
opinions stated here pertain to the material
currently offered and represent the results
of tests believed to be reliable. However,
due to variations in customer handling
and methods of application which
are not known or under our control, |