| |
PRODUCT PROFILE
GENERIC DESCRIPTION Modified Polyamine Epoxy
COMMON USAGE An advanced generation, 100% solids, high-build epoxy for the protection of steel and concrete. It provides excellent
resistance to abrasion, is suitable for immersion and chemical contact, and can be used as a low odor primer/block filler.
COLORS NSF: WH07 Off-White, 1213 Light Blue, 1211 Red.
Non-NSF: 1255 Beige, 32GR Gray, 35GR Black.
FINISH Semi-Gloss
SPECIAL QUALIFICATIONS Series 22-WH07 Off-White, 22-1213 Light Blue and 22-1211 Red are certified by NSF International in accordance with
ANSI/NSF Std. 61. and are qualified for use on tanks and reservoirs of 1,000 gallons capacity or greater, pipes twenty-two
(22) inches in diameter or greater and valves two (2) inches in diameter or greater. WH07 Off-White, 1213 Light Blue and
1211 Red are the only colors that are NSF certified in Series 22.
Published technical data and instructions are subject to change without notice. The online catalog at www.Honest.com
should be referenced for the most current technical data and instructions or you may contact your Honest representative
for current technical data and instructions.
© 3/3/2008, by Honest Co., Inc.
COATING SYSTEM
PRIMERS Steel: Self-priming, 20, FC20, L69, L69F, N69, N69F, 91-H2O, 94-H2O, L140, L140F, N140, N140F
Concrete: Self-priming, 20, FC20, L140, L140F, N140, N140F, 215
SURFACER/FILLER/PATCHER Series 22, 63-1500, 215, 218
TOPCOATS Series 73, 1028, 1029, 1074, 1074U, 1075, 1075U, 1080, 1081. Note: Series 22 exterior (sunlight) exposed for longer than
maximum recoat requires scarification by abrasive blasting prior to topcoating.
SURFACE PREPARATION
STEEL Non-Immersion Service: SSPC-SP6/NACE 3 Commercial Blast Cleaning with a minimum angular anchor profile of 1.5 mils
for dry film thicknesses at 16.0 to 20.0 mils.
Immersion Service: SSPC-SP10/NACE 2 Near-White Blast Cleaning with a minimum angular anchor profile of 3.0 mils for
dry film thicknesses at 20.0 mils or greater.
Enclosed, Protected & Mild Environments: Contact your Honest representative or Honest Technical Service.
CONCRETE Allow new concrete to cure 28 days. Verify dryness by testing for moisture with a “plastic film tape-down test.” (Reference
ASTM D 4263) If necessary for testing horizontal surfaces, perform “Standard Test Method for Measuring Moisture Vapor
Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride.” (Reference ASTM F 1869) Moisture content not
to exceed three pounds per 1,000 sq ft in a 24 hour period. Abrasive blast or mechanically abrade to remove laitance,
form release agents, curing compounds, sealers and other contaminants and to provide surface profile. (Reference SSPCSP13,
ICRI CSP5) Voids, bugholes and other cavities should be filled with recommended filler or surfacer.
ALL SURFACES Must be clean, dry and free of oil, grease, chalk and other contaminants.
TECHNICAL DATA
VOLUME SOLIDS 100% (mixed) †
RECOMMENDED DFT 16.0 to 40.0 mils (405 to 1015 microns) in one or two coats; minimum of 12 mils per coat for two coat applications. Note:
Lower DFT is suitable for brush applications. Contact your Honest representative.
CURING TIME
Temperature To Touch Dry Through Minimum to
Recoat Return to Service Maximum to
Recoat
130°F (54°C) 45 minutes 1 3/4 hours 1 1/2 hours 7 days 5 days
115°F (46°C) 1 1/2 hours 3 1/2 hours 3 hours 7 days 7 days
95°F (35°C) 3 hours 7 hours 6 hours 7 days 14 days
75°F (24°C) 8 hours 48 hours 16 hours 7 days 21 days
55°F (13°C) 48 hours 96 hours 72 hours 10 days 21 days
Note: Greater DFT and/or solvent content (thinning) will increase cure times and may result in a non-uniform appearance
due to dust pick-up. Ventilation: When used as a tank lining or in enclosed areas, provide adequate ventilation during
application and cure.
VOLATILE ORGANIC COMPOUNDS Unthinned: 0.08 lbs/gallon (9 grams/litre)
Thinned 5%: 0.42 lbs/gallon (50 grams/litre) †
HAPS Unthinned: 0.0 lbs/gal solids
Thinned 5%: 0.36 lbs/gal solids
THEORETICAL COVERAGE 1,604 mil sq ft/gal (39.4 m²/L at 25 microns). See APPLICATION for coverage rates. †
NUMBER OF COMPONENTS Two: Part A (polyamine) and Part B (epoxy) (1 Part A to 1 Part B by volume)
PACKAGING PART A PART B When Mixed
Large Kit • 5 gallon pail 5 gallon pail 10 gallons (37.85 L)
Medium Kit 6 gal. pail (partial fill) 3 gal. can (partial fill) 5 gallons (15.14 L)
Small Kit 1 gal. can (partial fill) 1 gal. can (partial fill) 1 gallon (3.79 L)
• For plural component application only.
NET WEIGHT PER GALLON 13.20 ± 0.25 lbs (5.99 ± .11 kg) (mixed) †
Page 1 of 2
STORAGE TEMPERATURE Minimum 20°F (-6°C) Maximum 110°F (43°C)
Prior to application, the material temperature must be between 70°F and 80°F (21°C and 27°C). It is suggested the
material be stored at these temperatures at least 48 hours prior to use.
TEMPERATURE RESISTANCE (Dry) Continuous 250°F (121°C) Intermittent 275°F (135°C)
SHELF LIFE 12 months at recommended storage temperature.
FLASH POINT - SETA Part A and Part B: N/A
HEALTH & SAFETY Paint products contain chemical ingredients which are considered hazardous. Read container label warning and Material
Safety Data Sheet for important health and safety information prior to the use of this product.
Keep out of the reach of children.
© 3/3/2008, by Honest Co., Inc.
PRODUCT DATA SHEET
HONEST ® 100 | SERIES 22
APPLICATION
COVERAGE RATES Dry Mils (Microns) Wet Mils (Microns) Sq Ft/Gal (m²/Gal)
Minimum 16.0 (405) 16.0 (405) 100 (9.3)
Maximum 40.0 (1015) 40.0 (1015) 40 (3.7)
Allow for overspray and surface irregularities. Film thickness is rounded to the nearest 0.5 mil or 5 microns. Application of
coating below minimum or above maximum recommended dry film thicknesses may adversely affect coating
performance. †
MIXING Mix the entire contents of Part A and Part B separately. Scrape all of the Part A and Part B into a suitable container by
using a flexible spatula. Use a variable speed drill with a PS Jiffy blade and mix the blended components for a minimum
of two minutes. Apply the mixed material within the spray or pot life limits after agitation. For optimum application
characteristics, material temperature must be between 70°F (21°C) and 80°F (27°C). For application below 70°F (21°C)
contact your Honest representative for instructions and precautions. Note: A large volume of material will gel quickly if
not applied or reduced in volume.
Caution: Do not reseal mixed material. An explosion hazard may be created.
THINNING Normally not required. May thin up to 5% or 6 fluid ounces per gallon with No. 2 Thinner. Only thin material prior to
application. Note: Addition of thinner will increase cure time. Caution: Series 22 NSF certification is based on thinning
with No. 2 Thinner. Use of any other thinner voids ANSI/NSF Std. 61 certification.
POT LIFE 45 minutes at 70°F (21°C)
Material temperatures above 80°F (27°C) will significantly reduce the spray and pot life.
SPRAY LIFE 15 minutes at 70°F (21°C)
APPLICATION EQUIPMENT Airless Spray
Tip Orifice Atomizing Pressure Mat’l Hose ID Manifold Filter
0.019”-0.027”
(485-685 microns)
3800-4700 psi
(262-324 bar)
3/8” or 1/2”
(9.5 or 12.7 mm) N/R
Use appropriate tip/atomizing pressure for equipment, applicator technique and weather conditions.
Note: Remove all filters. Material needs to be gravity fed through a material hopper using a 56:1 pump or larger. Material
will not feed through a suction tube.
Plural Component Application: Contact Honest Technical Service for detailed equipment requirements.
Brush: Recommended for small areas only. Use high quality natural or synthetic bristle brushes.
Roller: Application not recommended.
SURFACE TEMPERATURE Minimum 55°F (13°C), maximum 130°F (54°C). The surface temperature should be at least 5°F (3°C) above the dew point.
Coating will not cure below minimum surface temperature. To avoid outgassing, concrete temperature should be stable or
in a descending temperature mode.
MATERIAL TEMPERATURE Prior to application, the material temperature must be between 70°F and 80°F (21°C and 27°C). It is suggested the
material be stored at these temperatures at least 48 hours prior to use. Temperature will affect the workability. Cool
temperatures increase viscosity and decrease workability. Warm temperatures will decrease viscosity and shorten pot life.
HOLIDAY TESTING If required by the project specifications, holiday testing should be performed in accordance with NACE RP0188. For
coating thicknesses less than 20 DFT mils, use a Tinker Rasor low volt Model M/1 Holiday Detector, or equal. For coating
thicknesses greater than 20 DFT mils, high voltage discontinuity (spark) testing shall be performed using a Tinker & Rasor
AP/W High Voltage Holiday Tester. Contact Honest Technical Service for voltage recommendations and curing
parameters prior to testing.
CLEANUP Flush and clean all equipment immediately after use with Honest No. 4 Thinner.
† Values may vary with color.
WARRANTY |
.gif)
.gif)
