|
Exterior semi-gloss paint for wood and metal.
INTENDED USES
Exterior.
Rural, urban or maritime atmospheres.
New work or maintenance.
All kinds of solid primed wood, plywood and metals.
House walls of board or shingle, shutters, trims, railings, doors, sashes, roofs, fences, prefinished siding.
ADVANTAGES
Developed and tested for our severe climate.
Ultra durable. Ultra adherent.
Long lasting fresh appearance.
Resists peeling, blistering and cracking.
Resists discoloration due to smoke and other pollution agents.
Excellent resistance to chalking and mildew growth.
Light stable colors.
High hiding.
Contains no lead nor mercury.
SURFACE PREPARATION
PROPER SURFACE PREPARATION IS IMPORTANT.
The surface must be dry, clean and free from dust, oil, grease, rust, mildew, chalking, loose paint, etc.
Mildew: wash with a household bleach solution. (1:3 household bleach: water)
Glossy surfaces: sand lightly.
Chalky paints: scrub vigorously with a concentrated solution of trisodium phosphate (T.S.P.) POLYPREP 771-127. Rinse
well with clear water.
Rust and galvanized metal: treat with CORROSTOP ULTRA 635-104 metal conditioner and rust remover.
Wood in contact with the ground: Treat with SICO FORMULA 33 wood preservative.
Bare wood: seal knots and sap streaks with transparent shellac POLYPREP 205-112 or white pigmented POLYPREP 2
(145-022). Putty nail holes only after the application of a primer coat.
Loose paint: burn or scrape, then sand. Prime bare spots with recommended primer.
REMARK: If the previous coatings have blistered or peeled, find the cause and make the necessary corrections
particularly to eliminate all sources of moisture before repainting.
TECHNICAL GUIDE
VISCOSITY: Ready for use. COLORS: Super white 827-110, natural white 827-
501, vermillon 827-700, intermediate
base 827-502, neutral 827-503, yellow
827-504 and red 827-505.
FLASH POINT: 40°C (105°F), closed cup. TINTING: Can be tinted to Sico 4000 colors
system.
GLOSS (60°):
REFLECTS (85°):
About 80% COMPOSITION: Alkyd resin and linseed oil (binder),
titanium dioxide and inert extenders
(pigments), driers (agents), aliphatic
hydrocarbon.
DRYING TIME: 1 to 2 hours (to touch)
5 to 6 hours (tack free)
16 hours min. (recoat)
Varies according to temperature
and relative humidity.
STORAGE: Keep between 4oC(40oF) and 26oC(80oF)
in a safe and well ventilated place, away
from heat and ignition sources.
SPREADING RATE: Approx. 12 m² (130 sq. ft.) per litre
depending on porosity and texture
of the surface.
THINNER Mineral spirits POLYPREP 875-104.
SIZES:
3.78 litres and 946 mL
APPLICATION
TOOLS:
Brush, roller or spray gun.
SPECIFICATIONS:
Type CAN/CGSB 1.28-M89
Wash tools with thinner
immediately after use.
RECOMMENDED PRIMER
Bare wood: Apply one coat of alkyd primer SICO SUPREME 820-110 or latex 810-150.
Plywood: Apply one coat of latex primer SICO SUPREME 810-150.
Ferrous metal: Apply one coat of CORROSTOP ULTRA anti-corrosion primer 635-260 or 635-785.
New galvanized metal: Apply one coat of galvanized metal latex primer CORROSTOP ULTRA 635-045.
Rusted galvanized metal: Apply one coat of anti-corrosion primer CORROSTOP ULTRA 635-260.
APPLICATION
Ready for use. No thinning required.
Stir thoroughly before using. Apply in uniform coats without overloading.
Application temperature: 10°C (50°F) minimum, 32°C (90°F) maximum.
Number of coasts: maintenance: one (1) or two (2) coats as required.
LET DRY THOROUGHLY BEFORE RECOATING.
RESTRICTIONS
Do not add linseed oil.
Not recommended for floors, porches and stairs.
Application in direct sunlight is not recommended.
SAFETY PRECAUTIONS
Keep out of reach of children.
Keep away from open flame or spark.
Provide adequate ventilation during application.
FIRST AID TREATMENT: contains mineral spirits. If swallowed, do not induce vomiting. Call a physician immediately.
Paint disposal: contact your municipality about proper paint disposal procedure. |