|
MSDS EPOXY MOISTURE BARRIER PART B
10/07/2004
1
Chemical Safety Data Sheet
Section 1 -- PRODUCT AND COMPANY IDENTIFICATION
-----------------------------------------------------------------------------------------------------------------------
PRODUCT NAME: EPOXY MOISTURE BARRIER PART B
MANUFACTURER'S NAME: SHENZHEN FEIYANG CHEMICAL CO. LTD
ADDRESS : 1# FEIYANG RD. SHAJING, BAOAN SHENZHEN CHN
POSTCODE: 518104
EMERGENCY PHONE : +86(755) 33856588 DATE PRINTED: 10/07/04
INFORMATION PHONE: +86(755)-2640403 Fax: +86(755) 2723-7525
Website:WWW.FEIYANG.COM.CN
Section 2 -- COMPOSITION/INFORMATION ON INGREDIENTS
--------------------------------------------------------------------------------------------------------------------------------------------------
REPORTABLE COMPONENTS CAS NUMBER WEIGH%(MAX)
---------------------------------------------------------------------------------------------------------------------------------------------------
Epoxy Polymer
Alkyl Glycidyl Ether
Barium Sulfate
Silica, Amorphous
Titanium Dioxide
Unavailable
068609-97-2
007727-43-7
007631-86-9
013463-67-7
96
15.2
13.7
24.1
17.4
Section 3 -- HAZARDS IDENTIFICATION
--------------------------------------------------------------------------------------------------------
HAZARD CLASSIFICATION: LEVEL 3
ROUTES OF EXPOSURE
INHALATION of vapor or spray mist.
EYE or SKIN contact with the product, vapor or spray mist.
EFFECTS OF OVEREXPOSURE
EYES: Irritation.
SKIN: Prolonged or repeated exposure may cause irritation.
INHALATION: Irritation of the upper respiratory system.
May cause nervous system depression. Extreme overexposure may result in
unconsciousness and possibly death.
SIGNS AND SYMPTOMS OF OVEREXPOSURE
Headache, dizziness, nausea, and loss of coordination are indications of excessive
exposure to vapors or spray mists.
Redness and itching or burning sensation may indicate eye or excessive skin exposure.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE May cause allergic skin
reaction in susceptible persons or skin
sensitization.
ROUTES OF EXPOSURE
MSDS EPOXY MOISTURE BARRIER PART B
10/07/2004
2
INHALATION of vapor or spray mist.
EYE or SKIN contact with the product, vapor or spray mist.
EFFECTS OF OVEREXPOSURE
EYES: Irritation.
SKIN: Prolonged or repeated exposure may cause irritation.
INHALATION: Irritation of the upper respiratory system.
May cause nervous system depression. Extreme overexposure may result in
unconsciousness and possibly death.
SIGNS AND SYMPTOMS OF OVEREXPOSURE
Headache, dizziness, nausea, and loss of coordination are indications of
excessive exposure to vapors or spray mists.
Redness and itching or burning sensation may indicate eye or excessive
skin exposure.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
May cause allergic skin reaction in susceptible persons or skin
sensitization.
Section 4 -- FIRST AID MEASURES
--------------------------------------------------------------------------------------------------------
EYES: Flush eyes with large amounts of water for 15 minutes.
Get medical attention.
SKIN: Wash affected area thoroughly with soap and water.
If irritation persists or occurs later, get medical
attention.
Remove contaminated clothing and launder before re-use.
INHALATION: If affected, remove from exposure. Restore breathing.
Keep warm and quiet.
INGESTION: Do not induce vomiting.
Get medical attention immediately.
Section 5 -- FIRE FIGHTING MEASURES
----------------------------------------------------------------------------------------------------
FLASH POINT LEL UEL
20 F PMCC 1.0 10.9
FLAMMABILITY CLASSIFICATION
RED LABEL -- Extremely Flammable, Flash below 21 F
EXTINGUISHING MEDIA
Carbon Dioxide, Dry Chemical, Foam
UNUSUAL FIRE AND EXPLOSION HAZARDS
Closed containers may explode when exposed to extreme heat.
Application to hot surfaces requires special precautions.
During emergency conditions overexposure to decomposition products may
cause a health hazard. Symptoms may not be immediately apparent. Obtain
medical attention.
MSDS EPOXY MOISTURE BARRIER PART B
10/07/2004
3
SPECIAL FIRE FIGHTAING PROCEDURES
Full protective equipment including self-contained breathing apparatus
should be used.
Water spray may be ineffective. If water is used, fog nozzles are
preferable. Water may be used to cool closed containers to prevent
pressure build-up and possible autoignition or explosion when exposed to
extreme heat.
Section 6 -- ACCIDENTAL RELEASE MEASURES
-------------------------------------------------------------------------------------------------------
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED
Remove all sources of ignition. Ventilate the area.
Remove with inert absorbent.
Section 7 -- HANDLING AND STORAGE
---------------------------------------------------------------------------------------------------------
STORAGE CATEGORY
DOL Storage Class IB
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE
Contents are EXTREMELY FLAMMABLE. Keep away from heat, sparks, and open
flame. Vapors will accumulate readily and may ignite explosively.
During use and until all vapors are gone: Keep area ventilated - Do not
smoke - Extinguish all flames, pilot lights, and heaters - Turn off stoves,
electric tools and appliances, and any other sources of ignition.
Consult NFPA Code. Use approved Bonding and Grounding procedures.
Keep container closed when not in use. Transfer only to approved
containers with complete and appropriate labeling. Do not take internally.
Keep out of the reach of children.
Section 8 -- EXPOSURE CONTROLS/PERSONAL PROTECTION
-------------------------------------------------------
PRECAUTIONS TO BE TAKEN IN USE
Use only with adequate ventilation. Avoid contact with skin and eyes. Avoid breathing
vapor and spray mist. Wash hands after using. This coating may contain materials
classified as nuisance particulates which may be present at hazardous levels only during
sanding or abrading of the dried film.
VENTILATION
Local exhaust preferable. General exhaust acceptable if the exposure to
materials is maintained below applicable exposure limits.
If personal exposure cannot be controlled below applicable limits by
ventilation, wear a properly fitted organic vapor/particulate respirator
PROTECTIVE GLOVES
Wear gloves which are recommended by glove supplier for protection
MSDS EPOXY MOISTURE BARRIER PART B
10/07/2004
4
against materials in Section 2.
EYE PROTECTION
Wear safety spectacles with unperforated side shields.
OTHER PROTECTIVE EQUIPMENT
Use of barrier cream on exposed skin is recommended.
OTHER PRECAUTIONS
This product must be mixed with other components before use. Before
opening the packages, READ AND FOLLOW WARNING LABELS ON ALL
COMPONENTS.
Intentional misuse by deliberately concentrating and inhaling the
contents can be harmful or fatal.
Section 9 -- PHYSICAL AND CHEMICAL PROPERTIES
-------------------------------------------------------
SPECIFIC GRAVITY 3300g/gal
0
BOILING POINT 56 - 114 C
MELTING POINT Not Available
SOLUBILITY IN WATER N.A.
Section 9 -- REACTIBITY DATA
-------------------------------------------------------
STABILITY: Stable
CONDITIONS TO AVOID
Excessive temperatures. Avoid all heat sparks and sources of ignition.
INCOMPATIBILITY (MATERIALS TO AVOID)
Strong oxidizing agents (Nitric Acid, Permaganates, MEK Peroxide, Etc.).
HAZARDOUS DECOMPOSITION OR BYPRODUCTS
Normal combustion forms carbon dioxide and water vapor; incomplete combustion
can produce carbon monoxide.
Section 10 - DISPOSAL CONSIDERATIONS
-------------------------------------------------------
KIND OF WASTE DISPOSAL:Hazardous Waste
TREATMENT:Treatment and disposal must be in accordance with applicable provincial and
local regulations. Contact expertise before disposal. Refer to manufacturer/supplier for information on
recovery/recycling.
MSDS EPOXY MOISTURE BARRIER PART B
10/07/2004
5
Section 11 - TRANSPORTATION INFORMATION
-------------------------------------------------------
UN NUMBER:1993
PACKAGE LABEL: FLAMABLE LIQUID
PACKAGE CLASSFICATION: III
PACKAGE METHOD: METAL TIN
Keep container closed when not in use. Transfer only to approved containers with
complete and appropriate labeling. Do not take internally.
Keep out of the reach of children.
Section 12 -- REGULATORY INFORMATION
-------------------------------------------------------
Regulations:Safety Regulation for Hazardous Chemicals
Detail Application Rules of Safety Regulation for Hazardous Chemicals
Rules of Using Chemical Safely at Working Spot
Cass and Sign For Common Hazardous Chemicals (GB13690-92)
General Technique Conditions For Transportation and Packing
Hazardous Goods (GB12463-90)
Section 13 -- OTHER INFORMATION
-------------------------------------------------------
References:1. Safety Management for Chemicals at Woking Spot
2. Safety Handbook for Hazardous Goods
3 . All-Round Book for Safety Technology Hazardous Chemicals
4 . Register Regulation for Hazardous Chemicals
Writing Orginization:Shenzhen Feiyang Chemical Co,ltd.
Data Inspected by:Shenzhen Feiyang Chemical Co,ltd.
Writing Account:Writing according to Rules for Writing MSDS (GB16483-2000).
Others:
MSDS EPOXY MOISTURE BARRIER PART B
10/07/2004
6
The data in this Chemical Safety Data Sheet relates only to the specific material
designated herein and does not relate to use in combination with any other material or in
any process.
This information is based upon technical information believed to be reliable. It is
subject to revision as additional knowledge and experience is gained.
End of MSDS
|