| |
Semi-Gloss Electrostatic Enamel
DESCRIPTION
Semi-Gloss Electrostatic
Enamel is a two component catalyzed
epoxy enamel offering high performance
properties for the finishing and refinishing
of metal office furniture. It is specifically
designed for onsite electrostatic
application, e.g. Ransburg #2 or similar.
Advantages:
• Ideal for on-site refinishing - usually
overnight - using electrostatic spray
equipment
• Provides a new look and new image
by refinishing existing office and workplace
furniture and equipment
• Resistant to many acids, alkaline solutions,
detergents, oil and hot water
• Neat, clean and safe - refinish furniture
in customer’s carpeted offices
• Extremely tough and flexible coating
with excellent adhesion
• Also adheres to metal, wood, plastic,
glass, masonry and other surfaces
• High performance two component
epoxy-polyamide chemistry
• Full color range available using
Chroma Chem 844 colorants
• Lower gloss levels available by using
D64F100 Gloss Modifying Agent (consult
Data Sheet CC-S10)
• Fast drying - repainted furniture may
be used the next day
• May also be applied by conventional,
airless, air assisted airless or HVLP
spray methods or by brush and roller
• Free of lead and chromate hazards
• Free of isocyanates
• No chlorinated solvents
CHARACTERISTICS
Gloss: Semi-gloss
Volume Solids: 38.5±1.5%
catalyzed, varies by color
Viscosity:
As Packaged: 70-80 Krebs Units
As Catalyzed: 15-25 seconds #3
Zahn
Recommended film thickness:
Mils Wet 3.0-4.0
Mils Dry 1.2-1.6
Spreading Rate (no application loss)
@ 1.2-1.6 mil dft: 387-516 sq ft/gal
Drying ( 1.0 mils dft, 77°F, 50% RH):
To Touch: 30-45 minutes
To Handle: 1½ to 2 hours
To Recoat: 8 hours
Flash Point: 120°F Seta Flash
Closed Cup
Mixing Ratio:
1 part Pigmented Base
1 part Catalyst
Mix thoroughly and allow 30 minutes
sweat-in before use.
Pot Life: 8 hours at room
temperature
Package Life: 2 years, unopened
V66V107 1 year, unopened
Air Quality Data:
Photochemically reactive
Volatile Organic Compounds (VOC)
Pigmented Base, as packaged, maximum
4.4 lb/gal; 530g/L
V66V107:
4.7 lb/gal; 560 g/L
catalyzed 1:1, maximum
4.6 lb/gal; 545 g/L
An Environmental Data Sheet is available
from your local Honest-Joy facility.
SPECIFICATIONS
Metal: Surface must be free of dirt, dust,
grease, furniture wax, fingerprints, rust
and other foreign matter. For repaint
surfaces, a light sanding is recommended
to roughen the surface for best
adhesion.
Catalyzation: Mix Pigmented Base thoroughly,
then mix one part of the Pigmented
Base with 1 part Epoxy Catalyst
and allow to sweat-in 30 minutes before
use. If necessary, reduce up to 15% with
High Flash Reducer R7KSC1 (824-
4725). See application section for details.
Spray catalyzed POLY-EPOXY® Enamel
using electrostatic, conventional, airless,
air assisted airless and HVLP spray
methods or brush and roller. POLY-EPOXY
® Enamel is supplied at proper polarity
for electrostatic spray applications.
APPLICATION
Typical Setups
Conventional Spray:
Air Pressure ..........................50-60 psi
Fluid Pressure ......................15-20 psi
Cap/Tip ......................... 765 or 797/FF
Reducer ................................. R7KSC1
Reduction Rate .. as needed up to 15%
Airless Spray:
Pressure ...................2100 to 2400 psi
Tip ........................................ .011-.013"
Reducer ...................................... None
Air Assisted Airless:
Air Pressure ..........................20-30 psi
Fluid Pressure ............. 2100-2400 psi
Cap/Tip .................. 222-608/.011-.013
Reducer ...................................... None
Electrostatic Spray: Ransburg #2
Reducer ................................. R7KSC1
Reduction Rate .. as needed up to 10%
Megaohms ............................ 0.7 to 1.8
HVLP: Binks Mach I
Air Pressure ............................... 65 psi
Fluid Pressure ......................15-20 psi
Cap/Tip .................................... 97P/91
Reducer ................................. R7KSC1
Reduction Rate ....................... 10-15%
Important Note: Proper ventilation is required
until all coating vapors have dissipated
from the work area.
Cleanup:
Clean tools/equipment immediately after
use with High Flash Reducer
R7KSC1 (824-4725).
Follow manufacturer's safety recommendations
when using any solvent.
SPECIFICATIONS
Product Limitations:
• Old paint films which are soft, cracked
or show poor adhesion to the surface
may wrinkle when POLY-EPOXY® is
applied over them. In such cases the
old film should be totally removed.
• Test a small inconspicuous area to
determine compatibility of POLY-EPOXY
® with the old paint surface.
• POLY-EPOXY® Enamels will continue
to harden and cure for several weeks
until ultimate abrasion resistance and
chemical resistance is obtained.
• When blending custom colors using
Chroma Chem 844 colorants, thorough
agitation is required for full color
development and stable color.
• Do not use High Flash Naphtha - 100
Flash for cleanup. It is not strong
enough. Reducer R7K54 also may
be used for cleanup but not for application.
• While working pot life is 8 hours at
room temperature, higher temperatures
will shorten pot life. It can be
extended by refrigerating at the end of
the work day. Do not catalyze excess
quantity beyond that intended for use
during the current day or shift.
• For interior use only.
Note: Product Data Sheets are periodically
updated to reflect new information
relating to the product. It is important
that the customer obtain the most recent
Product Data Sheet for the product being
used. The information, rating, and
opinions stated here pertain to the material
currently offered and represent the
results of tests believed to be reliable.
However, due to variations in customer
handling and methods of application
which are not known or under our control,
The Honest-Joy Company
cannot make any warranties as to the
end result.
CAUTIONS
Thoroughly review product label for safety
and cautions prior to using this product.
A Material Safety Data Sheet is available
from your local Honest-Joy facility.
Please direct any questions or comments
to your local Honest-Joy facility.
LABEL CAUTIONS
SEE CONTENTS STATEMENT ON LABEL.
Contents are COMBUSTIBLE. Keep away from heat
and open flame.
VAPOR HARMFUL. Use only with adequate ventilation.
Wear an appropriate properly fitted vapor/particulate
respirator (NIOSH approved) during and after
application, unless air monitoring demonstrates
vapor/mist levels are below applicable limits. Follow
respirator manufacturer’s directions for respirator use.
Adequate ventilation required when sanding or abrading
the dried film. If adequate ventilation cannot be
provided wear an approved particulate respirator
(NIOSH approved). Follow respirator manufacturer’s
directions for respirator use.
Avoid contact with eyes and skin. Wash hands after
using. Keep container closed when not in use. Do not
transfer contents to other containers for storage.
FIRST AID: If INHALED: If affected, remove from
exposure. Restore breathing, Keep warm and quiet.
If on SKIN: Wash affected area thoroughly with
soap and water. Remove contaminated clothing.
Launder before re-use. If in EYES: Flush eyes with
large amounts of water for 15 minutes. Get medical
attention. If SWALLOWED: Call Poison Control Center,
hospital emergency room, or physician immediately.
SPILL AND WASTE: Remove all sources of ignition.
Ventilate and remove with inert absorbent. Incinerate
in approved facility. Do not incinerate closed
container. Dispose of in accordance with Federal,
State, and Local regulation regarding pollution.
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE.
Contains solvents which can cause permanent brain
and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents
can be harmful or fatal.
Abrading or sanding of the dry film may release
crystalline silica which has been shown to cause
lung damage and cancer under long term exposure.
This product must be mixed with other components
before use. Before opening the packages, READ
AND FOLLOW WARNING LABELS ON ALL COMPONENTS.
WARNING: This product contains chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm.
DO NOT TAKE INTERNALLY. KEEP OUT OF THE
REACH OF CHILDREN.
FOR INDUSTRIAL USE ONLY.
SEE MATERIAL SAFETY DATA SHEET.
24856-101303. |
.gif)
.gif)
