| |
Features General Properties
• 100% solids
• Forms the necessary
foundation to support high
performance top coats
• Deep penetration
• No offensive odors
• Compatible with a variety of
top coats
• Excellent adhesion properties
• Low VOCs
• Can be applied to rusted
substrates prepared to SSPCSP2
Standard
Recommended For: Limitations:
• Do not apply when air and surface temperatures are below 50° F
(10° C). Surface must be at least 5° F above dew point
• Gloss reduction and slight tendency to yellow in presence of
ultraviolet light
• This product is best applied over itself
This product is recommended for a variety of uses: as a
penetrating sealer over tightly adhering rusted surfaces, as a
sealer/finish coat for concrete surfaces, as a bonding primer over
glossy and hard-to-coat surfaces such as galvanized steel, stainless
steel, zinc, chrome, copper, brass, aluminum, and other nonferrous
metals. Red Oxide Primer will also
bond to hard slick surfaces, such as porcelain, Formica®, and other
nonporous surfaces. Actual spread rate will depend on the
substrate porosity and application technique.
Technical Data Clear
Generic Type Modified Amine Cured Epoxy
Pigment Type None
Volume Solids (mixed as recommended) 99.8%
Floor Coating Application: Recommended 4-8 mils DFT
Coverage Rate: 200-400 sq. ft./gal.
Dry Time @ 70° F – To Touch 4 Hours
– To Recoat 16 Hours
Maximum Recoat Time @ 70° F 7 days
Dries By Chemical Cure
Dry Heat Resistance – Intermittent 350° F
Viscosity @ 70° F (mixed as recommended)85 – 90 KU
Flash Point (PMCC) > 250° F
60° Specular Gloss – Gloss 80% minimum
Surface Temperature At Application – Min. 50° F
– Max. 90° F
Surface must be dry and at least 5° above the dew point.
Reducer N/A
Reduction – Brush not recommended
– Roller not recommended
– Spray not recommended
Clean Up Thinner M94
Mixing Ratio (by volume) 1:0.875
Induction Time N/A
Pot Life @ 77° F 1 – 11/2 Hours
Weight Per Gallon (mixed as recommended) 9.0 lbs
Storage Temperature – Min. 35° F
– Max. 95° F
Volatile Organic Compounds (VOC)
**Unthinned Grams/Liter 1.9
Lbs./Gal. 0.0
Surface Preparation
All surfaces to be coated must be dry and free of dust, dirt, oil, grease, wax, or other contaminants that could interfere with coating
adhesion.
WARNING! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN
CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Carefully clean up with a HEPA vacuum and a wet mop. Before
you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log
on to www.epa.gov/lead.
Application Information
May be brushed, rolled, or sprayed; squeegee may be used for floor application. Do not exceed recommended film thickness; extra care
must be taken to ensure complete coverage of the surface.
Clean Up Instructions
Clean all equipment immediately after use with Aromatic Thinner (M94). Flushing spray equipment at noon break, with a thorough
cleaning at the end of the work day, is good work practice.
Environmental, Health & Safety Information
WARNING! CAUSES EYE AND SKIN IRRITATION. Contains Epoxy resin
CAUSES EYE, SKIN, NOSE AND THROAT IRRITATION. MAY CAUSE ALLERGIC SKIN REACTION
IMPORTANT: Designed to be mixed from two components (M35-00 and M35-84). Mixture will have hazards of both components. Before
opening packages, read all warning labels. Follow all precautions.
Keep away from heat and flame. Use only with adequate ventilation. Do not breathe vapors, spray mist or sanding dust. Do not get
in eyes or on skin. WEAR A PROPERLY FITTED VAPOR/PARTICULATE RESPIRATOR APPROVED BY NIOSH FOR USE WITH PAINTS, eye protection,
gloves, and protective clothing during application (or sanding) and until all vapors and spray mist are exhausted. In confined places or
in situation where continuous spray operations are typical, or if proper respirator fit is not possible, wear a positive-pressure, supplied air respirator
approved by NIOSH. In all cases, follow respirator manufacturer’s directions. Do not permit anyone without protection in the painting
area. Close container after each use.
FIRST AID: If affected by inhalation of vapors or spray mist, remove to fresh air. In case of eye contact, flush immediately with plenty of water
for at least 15 minutes and call a physician. For skin, wash thoroughly with soap and water. In case of ingestion, DO NOT induce vomiting.
Get medical help immediately.
IN CASE OF: FIRE – Use foam, CO2, dry chemical, or water fog. SPILL – Absorb with inert material and dispose of in accordance with
applicable regulations.
USE COMPLETELY OR DISPOSE OF PROPERLY. This product contains organic solvents which may cause adverse effects to the environment if
handled improperly. Disposal of wastes containing either organic solvents or free-liquids in landfills is prohibited. Dry, empty containers may
be recycled in a can recycling program. Local disposal requirements vary; consult your sanitation department or state-designated
environmental agency on disposal options.
PROTECT FROM FREEZING FOR PROFESSIONAL USE ONLY KEEP OUT OF REACH OF CHILDREN
Refer to Material Safety Data Sheet available from your retailer for further safety and handling information.
Warranty & Limitation of Sellers Liability
All statements made on any product label, product manual, product data sheets, technical data charts or specification charts contained
herein, are accurate to the best of our knowledge. The products and information are intended for use by persons having skill and knowhow
in the industry at their own discretion and risk. Benjamin Moore & Co. warrants only that its coatings represented herein meet the
formulation standards of Benjamin Moore & Co. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY THE SELLER,
EXPRESSED OR IMPLIED, STATUTORY, BY OPERATION OR LAW, OR OTHERWISE INCLUDING MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. Workmanship, weather, construction equipment, quality of other materials and other variables affecting the
results are beyond our control. No agent, employee or representative of seller has any authority to bind seller to any affirmation,
representation or warranty except as stated above.
Red Oxide Primer |
.gif)
.gif)
